[Free] 2018(Jan) EnsurePass Testking Juniper JN0-643 Dumps with VCE and PDF 41-50

Ensurepass.com : Ensure you pass the IT Exams
2018 Jan Juniper Official New Released JN0-643
100% Free Download! 100% Pass Guaranteed!
http://www.EnsurePass.com/JN0-643.html

Enterprise Routing and Switching, Professional (JNCIP-ENT)

Question No: 41 – (Topic 1)

You need to enable authentication for your multiarea OSPF network. In this scenario which three statements are correct? (Choose three)

  1. MDS and simple authentication types are mutually exclusive

  2. IPsec is only supported on OSPFv3

  3. OSPF authentication is performed at the area level, and all devices in the same area must use same type of authentication and same password

  4. IPsec transport mode is supported

  5. IPsec tunnel mode is supported

Answer: A,C,D

Question No: 42 – (Topic 1)

You have certainly implemented the configuration shown in the exhibit. After committing these changes, the community devices connected to AS-1 are not able to communicate with the appropriate community devices connected to AS-2. What must be done to allow these community devices to communicate?

Ensurepass 2018 PDF and VCE

  1. You must configure an isolation VLAN ID Under the pvlan-200 on the AS2

  2. switch You must configure the ge-0/0/10 interface on AS1 AS THE VPLAN on both switches

  3. You must configure an isolation VLAN ID under the VLAN 200 ON both switches

  4. You must configure the ge-0/012 interface on both switches as P VLAN trunks

Answer: D

Question No: 43 – (Topic 1)

Referring to the exhibit, all host A has authenticated using 802.1X B. Which supplicant mode IS USED on the switch?

Ensurepass 2018 PDF and VCE

  1. MAC RADIUS

  2. Multiple

  3. Single

  4. Single-secure

Answer: C

Question No: 44 – (Topic 1)

Which policy statement will be applied to neighbor 172.16.4.2?

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

  1. policy-statement all and policy -statement agg

  2. policy-statement agg

  3. policy-statement all and policy -statement atat

  4. policy-statement atat

Answer: A

Question No: 45 – (Topic 1)

What must you add to the configuration to allow a receiver connected to interface ge 0/0/6 to subscribe to group 232.0.0.1 from source 172.16.7.1?

Ensurepass 2018 PDF and VCE

  1. Add sparse mode to PIM interface ge 0/0/6

  2. Add version 2 to the state RP configuration

  3. Add version 3 to IGMP interface ge 0/0/6

  4. Add version 2 to IGMP interface ge 0/0/6

Answer: C

Question No: 46 – (Topic 1)

A customer wants to connect computer and IP telephone equipment to a switch using the same port. LLDP-MED has been turned onto discover VoIP equipment. Which two statements are true in this scenario? (Choose two)

  1. the switch will identify voice traffic automatically based on the source MAC address

  2. the access port can be configured to accept both tagged voice traffic and untagged data traffic

  3. the computer and VOIP equipment must be in the same VLAN on an access port

  4. the switch can send configuration information to the IP phone to assign it a VLAN automatically

Answer: B,D

Question No: 47 – (Topic 1)

The network administrator wants the ports on an EX series switch to allow both tagged and untagged frames to be forwarded. Tagged frames should be associated with their tagged VLAN, while untagged frames should be associated with a preconfigured VLAN. In this scenario, which statement is true?

  1. The interface port mode should be configured as mixed mode to allow both trunk and access port modes, untagged frames will belong to the default VLAN configured on that post

  2. An interface can be configured as an access port or a trunk port, but it cannot accept both tagged and untagged frames

  3. The interface port mode should be configured as an access port with a VLAN ID, frames tflSrenter the port with a VLAN tag already assigned will override the access port vlan id

  4. The interface port mode should be configured as a trunk port, untagged fra^^swill belong to the native Vlan id configured on that port

Answer: D

Question No: 48 – (Topic 1)

Referring to the exhibit, traffic that uses destination port 22 and the code point alias of 101010 is entering the router on interface ge 0/0/1. In this scenario which two statements are true?

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

Ensurepass 2018 PDF and VCE

  1. The traffic is placed in the best effort forwarding class

  2. The traffic is evaluated by both classifiers

  3. The traffic is placed in the network control forwarding class

  4. The traffic is only evaluated by the multi-field classifier

Answer: A,B

Question No: 49 – (Topic 1)

Which statement describes 802 1x supplicant single modes?

  1. 802 1x supplicant single mode permit access for the first supplicant, all other applicants that connect to the port are allowed full access without further authentication

  2. 02 1x supplicant single mode allows all supplicant to connect to the port,each supplicant is authenticated individually

  3. 802 1x supplicant single mode permits access for a single supplicant,all other supplicants attempting to connect through the same port are denied access

  4. 802 1x supplicant single mode allows only one supplicant to connect to the port,no other supplicant is allowed to connect until the first supplicant disconnects

Answer: A

Question No: 50 – (Topic 1)

You configured IPv6 statics routes on the juniper routes and you want to OSPF to propagate these routes throughout your network. Which set of commands will accomplish these tracks?

  1. Set policy-options statement exportatatic term IPV6 static from protocol ospf Set policy options statement exportatatic term IPV6 static than accept Set protocols ospf3 export exportstatic

  2. set policy options statement exportatic term IPV6 static from protocol ospf Set policy options statement exportatic term IPV6 static than accept Set protocols ospf export exportstatic

    portexportstat

  3. set policy options statement exportstatic term IPV6 static from protocol static Set policy options statement exportstatic term IPV6 static than accept Set protocol ospf export exportstatic

  4. set policy options statement exportstatic term IPV6 static from protocol statie Set policy options statement exportstatic term IPV6 than accept Set protocol ospf3 export exportstatic

Answer: D

100% Ensurepass Free Download!
Download Free Demo:JN0-643 Demo PDF
100% Ensurepass Free Guaranteed!
Download 2018 EnsurePass JN0-643 Full Exam PDF and VCE

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.